drying natural gas hot water atmospheric pressure fire tube boiler
HOT
Capacity:1-20t/h
Rated thermal efficiency: 100-104%
Fixed working pressure: ≤1.6MPa
Applicable fuel:natural gas etc.
HOT
Capacity:0.7-14MW
Rated thermal efficiency:96-98%
Fixed working pressure:≤1.25MPa
Applicable fuel:Natural gas, light oil, etc.
HOT
Capacity:0.7-2.8Mw
Rated thermal efficiency: 97.2-106%
Fixed working pressure:0.1MPa
Applicable fuel:Natural gas, etc.
HOT
Capacity:2.8-7.0Mw
Rated thermal efficiency:≥105.5%
Fixed working pressure:-0.02MPa
Applicable fuel:Natural gas, etc.
HOT
Capacity:99Kw
Rated thermal efficiency:97.2-104.4%
Fixed working pressure:1.0MPa
Applicable fuel:Natural gas, etc.
HOT
Capacity:0.5-4.0 t/h
Rated thermal efficiency:98%
Fixed working pressure:≤1.25MPa
Applicable fuel:electric energy
The term boiler is applied to the single heat source that can supply either steam or hot water (a boiler is often called a heater). Boilers may be classified according to several kinds of characteristics. They are typically made from cast iron or steel. Their construction design may be sectional, portable, fire-tube, water-tube, or special.Get Price
A boiler or steam generator is a device used to create steam by applying heat energy to water.Although the definitions are somewhat flexible, it can be said that older steam generators were commonly termed boilers and worked at low to medium pressure (7–2,000 kPa or 1–290 psi) but, at pressures above this, it is more usual to speak of a steam generator.Get Price
The term boiler is applied to the single heat source that can supply either steam or hot water (a boiler is often called a heater). Boilers may be classified according to several kinds of characteristics. They are typically made from cast iron or steel. Their construction design may be sectional, portable, fire-tube, water-tube, or special.Get Price
7. Air enters a fan through a duct at a velocity of 6.3 m/s and an inlet static pressure of 2.5 cm of water less than atmospheric pressure. The air leaves the fan through a duct at a velocity of 11.25 m/s and a discharge static pressure of 7.62 cm of water above the atmospheric pressure.Get Price
Low pressure steam or hot water boiler means an electric, gas or oil burning furnace designed to supply low pressure steam or hot water for space heating application. A low pressure steam boiler operates at or below 15 pounds psig steam pressure; a hot water boiler operates at or below 160 psig water pressure and 250 °F. water temperature.Get Price
Containers used with systems embodied in paragraphs (d), (e), (g), and (h) of this section, except as provided in paragraphs (e)(3)(iii) and (g)(2)(i) of this section, shall be designed, constructed, and tested in accordance with the Rules for Construction of Unfired Pressure Vessels, section VIII, Division 1, American Society of Mechanical Engineers (ASME) Boiler and Pressure Vessel …Get Price
Where hot-water-heating boilers are connected to heating coils located in air-handling units where they can be exposed to refrigerated air circulation, such boiler piping systems shall be equipped with flow control valves or other automatic means to prevent gravity circulation of the boiler water during the cooling cycle. [NFPA 54:10.3.9.2]Get Price
7. Air enters a fan through a duct at a velocity of 6.3 m/s and an inlet static pressure of 2.5 cm of water less than atmospheric pressure. The air leaves the fan through a duct at a velocity of 11.25 m/s and a discharge static pressure of 7.62 cm of water above the atmospheric pressure.Get Price
Hazardous-waste and medical-waste incinerators usually have just convective boiler sections, typically of fire-tube rather than water-tube design. Most hazardous-waste and medical-waste incinerators, particularly the smaller units, do not have heat-recovery boilers. Combustion gases are quenched by water sprays atomized into the hot gas flow.Get Price
Where hot-water-heating boilers are connected to heating coils located in air-handling units where they can be exposed to refrigerated air circulation, such boiler piping systems shall be equipped with flow control valves or other automatic means to prevent gravity circulation of the boiler water during the cooling cycle. [NFPA 54:10.3.9.2]Get Price
Low-Pressure Steam and Hot Water Heating Systems. Hot water boilers heat and circulate water at approximately 200°F. Steam heating boilers are used to generate steam at low pressures, such as 15 psig. Generally, these two basic heating systems are treated as closed systems, because makeup requirements are usually very low.Get Price
A boiler or steam generator is a device used to create steam by applying heat energy to water.Although the definitions are somewhat flexible, it can be said that older steam generators were commonly termed boilers and worked at low to medium pressure (7–2,000 kPa or 1–290 psi) but, at pressures above this, it is more usual to speak of a steam generator.Get Price
Dec 01, 2016 · Figure 42. The gas-usage system at the Penn State anaerobic digester. A portion of the digester output is utilized in firing the boiler that provides hot water for maintaining slurry temperature at 95°F. Following cooling and reheating, an automatic pressure-reduction valve reduced the gas pressure in the line to about 12 in (30 em) water gage.Get Price
Low-Pressure Steam and Hot Water Heating Systems. Hot water boilers heat and circulate water at approximately 200°F. Steam heating boilers are used to generate steam at low pressures, such as 15 psig. Generally, these two basic heating systems are treated as closed systems, because makeup requirements are usually very low.Get Price
Dec 01, 2016 · Figure 42. The gas-usage system at the Penn State anaerobic digester. A portion of the digester output is utilized in firing the boiler that provides hot water for maintaining slurry temperature at 95°F. Following cooling and reheating, an automatic pressure-reduction valve reduced the gas pressure in the line to about 12 in (30 em) water gage.Get Price
Containers used with systems embodied in paragraphs (d), (e), (g), and (h) of this section, except as provided in paragraphs (e)(3)(iii) and (g)(2)(i) of this section, shall be designed, constructed, and tested in accordance with the Rules for Construction of Unfired Pressure Vessels, section VIII, Division 1, American Society of Mechanical Engineers (ASME) Boiler and Pressure Vessel …Get Price
Feel free to reach out if you want to collaborate with us, or simply have a chat.
